POLYPAIR-EPF

 

TYPICAL APPLICATIONS

 
- Slab on grade.
- Drive ways and parking lost 
- Sidewalks & Shot Crete Toppings. 
- Septic Tanks & other prepackaged items.
- Water Channels.
- Concrete Canals. 
 
PRODUCT FEATURES
 
- POLYFIBER-F is a 100% polypropylene   fiber.
-  Multifilament or collated Fibrillated Fibers.
- Fiber lengths range from 12.00 mm. To          
  19.00 mm.
- Additive included preventing ultraviolet 
  degradation.
- High bond strength to concrete matrix. 
- Excellent Fiber distribution. 
- Alkali & acid resistance, will not corrode  
  in the concrete.
 
PROPERTIES
 
Material 
Polypropylene
 
SPECIFIC GRAVITY 
0.90
FIBER TYPE  
Collated Fibrillated
 
FIBER LENGTH
12.00 mm. To 19.00 mm.
 
TOXICITY
 
Non toxic
 
WATER ABSORPTION
 
Nil
 
ALKALI RESISTANCE
 
High
 
ACID RESISTNCE
 
High
 
THERMAL CONDUCTIVITY
 
Low
 
MILDEW RESISTANCE
 
High
 
ELECTRIC CONDUCTIVITY 
Low
  
Colour
White
 
MELT POINT
 
170 *C
 
IGNITION POINT
Over 590 *C
 
FIBER TAPE THICKNESS
 
0.0965 mm. ** 10 %
 
YOUNG S MODULUS
 
3600
 
PLASTIC SHRINKAGE
 
100% reduction of plastic shrinkage cracking.
 
FREEZE - THAW
 
High Resistance
 
CHEMICAL RESISTANCE 
High Resistance To alkalis in concrete. POLYFIBER-F does not induce the growth of bacteria and algae.
 
PERMEABILITY
 
Dramatically decrease concrete Permeability.
 
BOND STRENGTH
 
Increase the bond between concrete & reinforcing steel.
 
IMPACT  RESISTANCE
 
Increase impact resistance of concrete.
  
COMPRESSIVE STRENGHT
Improves concrete compressive strength.
 
FLEXURAL STRENGTH
Increase flexural strength of concrete.
 
SPLIT TENSILE STRENGTH
 
Improves split tensile strength.
 
STABILITY
 
Is not effected by Ultra Violet Light.
 
STANDARDS
 
POLYFIBER-F is tested to the appropriate sections of the following Standards:
ASTM D-1204, ASTM D-638
 
GUIDE FOR APPLICATION
 
Processing 
POLYFIBER-F is packed in per measured bags with required projects size, ranging dose starts from 0.9 Kg Per cubic meter.
Add POLYFIBER-F into the mixer and mix for 4-5 minutes or 60-70 revolution at full speed to insure uniform distribution.
 
PLACING / FINISHING
 
Fiber reinforced concrete may appear slightly stiffer than plain concrete without affecting 
workability, it increases the concrete cohesive properties. 
However, if additional workability is required, a water reducer or super plasticizer should be used instead of adding water. 
This increase in cohesion will also reduce segregation, resulting in less or slower bleeding. With this in mind, it is important not to begin finishing too early.    
 
Guarantee / Warranty
 
We warrant our products to be of good quality and manufactured to rigid standards. This warranty is in lieu of any and all other warranties expressed or implied. 
This data sheet is published for information only. It is believed to be correct but no liability is accepted for it or the suitability of the product for any particular purpose. 
POLYCOO services are free and the company dose not accepts liability for any loss arising from it.
 
TECHNICAL SERVICES
 
For any further technical advice and recommendation for the use of all POLYCOO products, please consult the nearest POLYCOO technical office.
Finishing is accomplished best with steel or magnesium trowels and floats, wooden tools open the surface and may expose additional fibers. Also, it is not recommended to use a tin. 
???Rake to move or place fiber reinforced concrete. The tins can disrupt the fibers uniform three dimensional distributions.  
For exterior textured or broom finishes, use a dry stiff bristled broom.
If you require any special application please consult, POLYCOO – Technical department for dosage rate.
 
PACKAGING
 
Normally 0.9 kg. Per pack.

Quick Overview:

  • Short Description:

    POLYPAIR EPF is 3 components; solvent-free epoxy resin mortar based on a combination of epoxy resins and carefully selected & graded aggregates. It is formulated to provide after mixing the three components a thixotropic consistency mortar with high quality, abrasion & chemical resistance. It is suitable for use for horizontal, vertical and overhead patching & resurfacing to dry and damp surfaces. It is supplied in pre-weighed quantities: A (Resin), B (Curing Agent) and C (Aggregate) ready for

  • Files:

    POLYPAIR-EPF