POLY CLAY WATER STOP

 

POLYCLAY WATER STOP is specially formulated multiple composite water stop which swell upon contact with fresh and salt water.
It combines the strength & toughness to replace conventional water stops and can be applied without split forming or splicing as required with conventional water stops.
Its self healing ability is formed upon reacting with the leaking water to form a tight pressure seal when placed in a confined condition within a concrete cold joint.
 
Typical Applications
 
 It is applied in non moving concrete joints and between precuts concrete structures of
 
Manholes & Septic Tanks.
Box culverts &water structures.
Water & Waste water concrete pipes.
Foundations, slabs &retaining walls.
Underground parking garages.
Concrete storage tanks & tunnels.
Replacing conventional water stops.
Product Features
 
 The expansion properties engineered into 
POLYCLAY WATER STOP  :
 
Reduce the internal pressures created from traditional clay based expanding water stop.
Single component, easy to apply with high water proofing sealing ability.
Self healing joint waterproofing system. Eliminates many problems encountered with conventional P.V.C.& Rubber Water Stop as:
- Difficulties in positioning the water stop.
- Water migration along the water stop surface.
- Splicing and split forming.
 
Standards
 
POLYCLAY WATER STOP is tested to the    appropriate section of the following Standards:
 ASTM D-217
 ASTM D- 6
 ASTM D- 297
 ASTM D-71
 NSF approved for contact with potable water.
 
Properties
 
Colour
 Black
Specific Gravity 
1.35 + 0.05             (ASTM D-71)
Hydrocarbon Content 
47 %  min.                (ASTM D-297)
Volatile Matter 
1 % Max. .               (ASTM D-6)
Penetration Cone 
At 77oF, 150 gm: 5 sec.
40 +- 5    (ASTM D-217)
Carton Length 
30.48 m. RX 101
60.96 m. RX 102             
Application Temperature 
- 22°C to    +52°C
Service Temperature 
 - 34°C to   +34° C
 
Guide for Application
 POLYCLAY WATER STOP  used in poured in place concrete structures:
- Carefully brush off all dust and debris and apply a coat of an appropriate POLYCLAY WATER STOP  primer to the area where the POLYCLAY WATER STOP    has to be placed on the standing structural member
 - Using moderate hand pressure with the heel of the hand, press a continuous bead of POLYCLAY WATER STOP  firmly into position on the standing structure. Check to be certain that the sealant has bonded to the primed area.
- Peel the protective backing from the exposed side of the POLYCLAY WATER STOP. Knead the overlapped ends together to form a continuous uninterrupted gasket - Pour the concrete structural into position.
 
NOTE: When installing
 
POLYCLAY WATER STOP  on poured in place structures, always remember the following consideration:
- Place POLYCLAY WATER STOP  so it is within the outer 5Cm.of any vertical or horizontal construction joint. This usually occurs on the inside edge of the rebar extension.
If a keyway is formed, place POLYCLAY WATER STOP  into the formed keyway area. 
- Always use appropriate POLYCLAY WATER STOP  Primer Product to avoid displacement of the POLYCLAY WATER STOP  during concrete pouring.
- It may be necessary to utilize masonry nails to hold the water stop in place on vertical surfaces.
When masonry nails are used, they should be placed approximately 30cm.apart..
 
Shelf Life
One year
 
Packaging
POLYCLAY WATER STOP is available in two cross section sizes.
 
Cross Section      Rolls / Carton     Carton length
26 x 19 mm                     6                        30.48 m.
13 x 19 mm                    12                       60.96 m.
 
Guarantee / Warranty
 
We warrant our products to be of good quality and manufactured to rigid standards. This warranty is in lieu of any and all other warranties expressed or implied. 
This data sheet is published for information only. It is believed to be correct but no liability is accepted for it or the suitability of the product for any particular purpose. 
POLYCOO services are free and the company dose not accepts liability for any loss arising from it.
 
Technical Services
 
For any further technical advice and recommendation for the use of all POLYCOO products, please consult the nearest POLYCOO technical office.

Quick Overview:

  • Short Description:

    Cold Joint Expansion Live Sealing Water stop Product Description POLYCLAY WATER STOP is specially formulated multiple composite water stop which swell upon contact with fresh and salt water.

  • Files:

    POLY CLAY WATER STOP